Fitting Instructions

• Thoroughly clean and degrease the surface. Use Methylated Spirit or Isopropyl Alcohol to degrease.
• Cut the sheet into individual logos. ( Not individual letters )                                                                  
• Place a decal face down, rub all over, then peel off the backing ( squared paper ).                              
• Position the decal in the desired location then rub firmly all over.                                                          
• If the surface you are applying to is cold, heat with a hairdryer, then rub all over again.                       
• Peel off the application paper with care.                                                                                                
• If there are any air bubbles simply prick with a needle and push the air out.                                        

  These are non-genuine parts and are for restoration and replacement purposes only

This is not an original  Part.

Kadhesive TankPad Protector

Dimession 216 x 177 mm

Article ready to apply, with no changes at the moment; will be sent as pictured

21mil thick material specially formulated and widely used in the motocross industry.

With the best possible adhesive for low-energy surfaces, such as
MX plastics. The protective laminate is thick and durable enough to support professional motorcycles.

Size: 185 mm x 65 mm

Fitting Instructions

• Thoroughly clean and degrease the surface. Use Methylated Spirit or Isopropyl Alcohol to degrease.
• Cut the sheet into individual logos. ( Not individual letters )                                                                  
• Place a decal face down, rub all over, then peel off the backing ( squared paper ).                              
• Position the decal in the desired location then rub firmly all over.                                                          
• If the surface you are applying to is cold, heat with a hairdryer, then rub all over again.                       
• Peel off the application paper with care.                                                                                                
• If there are any air bubbles simply prick with a needle and push the air out.                                        

  These are non-genuine parts and are for restoration and replacement purposes only

This is not an original  Part.

Size: 90 mm x 75 mm

Fitting Instructions

• Thoroughly clean and degrease the surface. Use Methylated Spirit or Isopropyl Alcohol to degrease.
• Cut the sheet into individual logos. ( Not individual letters )                                                                  
• Place a decal face down, rub all over, then peel off the backing ( squared paper ).                              
• Position the decal in the desired location then rub firmly all over.                                                          
• If the surface you are applying to is cold, heat with a hairdryer, then rub all over again.                       
• Peel off the application paper with care.                                                                                                
• If there are any air bubbles simply prick with a needle and push the air out.                                        

  These are non-genuine parts and are for restoration and replacement purposes only

This is not an original  Part.

Size: 50 mm x 50 mm

Package: 1 Vinyl Sticker

Fitting Instructions

• Thoroughly clean and degrease the surface. Use Methylated Spirit or Isopropyl Alcohol to degrease.
• Cut the sheet into individual logos. ( Not individual letters )                                                                  
• Place a decal face down, rub all over, then peel off the backing ( squared paper ).                              
• Position the decal in the desired location then rub firmly all over.                                                          
• If the surface you are applying to is cold, heat with a hairdryer, then rub all over again.                       
• Peel off the application paper with care.                                                                                                
• If there are any air bubbles simply prick with a needle and push the air out.                                        

  These are non-genuine parts and are for restoration and replacement purposes only

This is not an original  Part.

Size: 77 mm x 35 mm

Fitting Instructions

• Thoroughly clean and degrease the surface. Use Methylated Spirit or Isopropyl Alcohol to degrease.
• Cut the sheet into individual logos. ( Not individual letters )                                                                  
• Place a decal face down, rub all over, then peel off the backing ( squared paper ).                              
• Position the decal in the desired location then rub firmly all over.                                                          
• If the surface you are applying to is cold, heat with a hairdryer, then rub all over again.                       
• Peel off the application paper with care.                                                                                                
• If there are any air bubbles simply prick with a needle and push the air out.                                        

  These are non-genuine parts and are for restoration and replacement purposes only

This is not an original  Part.

Size: 76 mm x 52 mm

Fitting Instructions

• Thoroughly clean and degrease the surface. Use Methylated Spirit or Isopropyl Alcohol to degrease.
• Cut the sheet into individual logos. ( Not individual letters )                                                                  
• Place a decal face down, rub all over, then peel off the backing ( squared paper ).                              
• Position the decal in the desired location then rub firmly all over.                                                          
• If the surface you are applying to is cold, heat with a hairdryer, then rub all over again.                       
• Peel off the application paper with care.                                                                                                
• If there are any air bubbles simply prick with a needle and push the air out.                                        

  These are non-genuine parts and are for restoration and replacement purposes only

This is not an original  Part.

Size: 85 mm x 45 mm

Fitting Instructions

• Thoroughly clean and degrease the surface. Use Methylated Spirit or Isopropyl Alcohol to degrease.
• Cut the sheet into individual logos. ( Not individual letters )                                                                  
• Place a decal face down, rub all over, then peel off the backing ( squared paper ).                              
• Position the decal in the desired location then rub firmly all over.                                                          
• If the surface you are applying to is cold, heat with a hairdryer, then rub all over again.                       
• Peel off the application paper with care.                                                                                                
• If there are any air bubbles simply prick with a needle and push the air out.                                        

  These are non-genuine parts and are for restoration and replacement purposes only

This is not an original  Part.

12 custom adhesive labels

 

Personalize your labels with information about your name, city where you live and blood type.

These tags can save a life.

Material: Sticker Vinyl

Waterproof

Enter the desired Coutry Flag name and blood type in the purchase order.

Water resistant stickers.

Ideal for identification in; Bags, Helmets, Bikes, Motorcycles, Guitars, etc ...


Set contains 8 Vinyl Tag Names.